www.flightsim4fun.com - rksoftware

Hello!

when i'm loading Oi4FS with the PMDG B737 v6.2.ssi i found that the Main panel DU are different from default configuration.
What's i'm wrong?

Thanks!
Sergio

I recommend that you use the latest version of PMDG 737 driver for MSFS and check if that takes care of your problem.



Send an request to roarkrsp@gmail.com and ask for the very latest version of the PMDG 737 driver for MSFS.

Negative at the test.
I see that when i make light test the DU cap and Fo knob move in not NORM POSITION...

Link of video
https://youtu.be/CzxPa2oGa0w

What is the version of the the PMDG 737 driver and the script you are using?

What is the text in the PMDG B737.ini file in Oi4FS folder?

Do you have a Dual or SIngle MIP panel module?

hello Roar,

i use 6.4 with servo flaps correction for matching my gauges.
its a single seat, with 1 input cards
[SIOC]
IOCP_port=8092
IOCP_timeout=4000
Minimized=Yes
toggle_delay=20
[IOCARDS MODULE]
IOCard_disable=No
IOCard_LPT=No
[FSUIPC MODULE]
FSUipcdisable=No
FSUipcRefresh=60
[IOCP CLIENTS MODULES]
IOCPini_delay=3000
IOCPclient0_disable=no
IOCPclient0_host=localhost
IOCPclient0_port=8099
IOCPclient1_disable=yes
IOCPclient1_host=localhost
IOCPclient1_port=8092
[SOUND MODULE]
Sound_disable=Yes
Volume=100
[*]
[PMDG B737]
CONFIG_FILE=C:\SIOC\Oi4FS\PMDG B737 mio v6.4.ssi
MASTER=31,4,2,111
MASTER=16,16,1,228
USBServos=36,112

As you have the single MIP module, the PMDG B737.ini's MASTER line for the MIP should be:

MASTER=31,4,1,111

if that doen't help

Try also to disable all inputs for the FO MIP part in the script.

This can be done by setting // in front of the script lines that you need to disable

Also change the Oi4FS.ini line:
MIP,IDX31m2
to
MIP,IDX31m1

so the next time you do a configuration it is correct for your hardware

question:

the MASTER=16,16,1,228 it the Chrono L
i need to remove?

I can be there, it is for the Chrono and should not interfer.
But, it is always best to just connect the device you have problems with when you are trying to find the root cause of your problem.

mvr1918 wrote: ↑Mon Mar 06, 2023 10:04 am I can be there, it is for the Chrono and should not interfer.
But, it is always best to just connect the device you have problems with when you are trying to find the root cause of your problem.

after weeks of try every time the script loading this happen

https://www.youtube.com/watch?v=IGDl0IoY3D8

if i put // on the following input the selector remain in the correct position
but obliusly i can use the selector inside the cockpit....

any solution?

Good day all
I discovered I have this same problem. When I start the PMDG737 immediately I put power on, the DUs for both Capt and FO will move to disagree with what I have on the MIP.
MIP DU postions would both be NORM (Capt and FO)
But the virtual cockpit DUs would move to Capt Main Panel DUs @ MFD and FO Main Panel DUs @ ENG PRI
And the Lower DUs for both Capt and FO would also disagree.
Please need help
I know I am using he most upto date software as I just join this family so I am not sure where to proceed.